Welcome, Guest. Please Login or Register
Welcome To Ask The Trades!
Mar 28th, 2024, 8:57pm
Quote: The best way to remember your wife's birthday is to forget it once.


Pages: 1 2 
Send Topic Print
Shower Diverter Valve Temperature (Read 5505 times)
Custard
Junior Member
**
Offline

Ask The Trades
Posts: 15


Total Thanks: 0
For This Post: 0



Shower Diverter Valve Temperature
May 19th, 2021, 3:26pm
 
Hello – thanks for looking at this – I'll try to be brief with just the facts:

• I have a Roper Rhodes SV1409 thermostatically controlled shower/diverter valve.
• It was installed by a plumber 4-5 years ago
• It worked very well up until a few months ago.
• The feed from the combi boiler is good and hot.
• There is a strong flow from both hot and cold.
• Even with the temperature control turned all the way up, the water temperature isn't quite hot enough. If I tease back and reduce the flow of the on/off control, I can make it a bit hotter.
• N.B. – the temperature stop retainer is not preventing rotation of the thermostat.
• So I have:
Removed and descaled the thermostatic cartridge.
Removed and cleaned/descaled the little hot-feed filter.
Finally – I REPLACED the thermostatic cartridge with a new one.

It remains the same with a not-so-hot 'hottest' temperature. I live in a flat and wonder if I should reduce the mains flow at the internal stopcock to get the same effect as easing back the flow with the on/off control valve (I have enough water pressure)?

Unless my water pressure has increased in the last few months, I can't understand why it no longer performs as it did. If I ran a bath, it really wouldn't be hot enough.

I have inserted a pic and diagram in case it helps.

Many thanks for your advice!

Roper Rhodes SV1409
Image 5
Back to top
 
Thank User For This Post View members image gallery  
IP Logged
 
thescruff
Global Moderator
Trade Member
Author
*****
Offline

Who said plumbing was
easy.
Posts: 6037


Total Thanks: 147
For This Post: 0


Gender: male

Trade: Plumber



Re: Shower Diverter Valve Temperature
Reply #1 - May 19th, 2021, 10:27pm
 
Did you adjust the cartridge as per the instruction?
Back to top
 
Thank User For This Post View members image gallery  
IP Logged
 
Custard
Junior Member
**
Offline

Ask The Trades
Posts: 15


Total Thanks: 0
For This Post: 0



Re: Shower Diverter Valve Temperature
Reply #2 - May 20th, 2021, 9:29am
 
The cartridge has no adjustment other than the spindle that rotates for the temperature. it just 'plugs' in and is retained by a nut and retaining sleeve.

If you are referring to adjusting it by way of the plastic temperature stop retainer, I am testing it with that off for the moment because I want to see what the maximum temperature could be without it being limited. It's still not very hot.

I don't feel that the cartridge can be the culprit as the old one was no worse than this one.
Back to top
 
Thank User For This Post View members image gallery  
IP Logged
 
thescruff
Global Moderator
Trade Member
Author
*****
Offline

Who said plumbing was
easy.
Posts: 6037


Total Thanks: 147
For This Post: 0


Gender: male

Trade: Plumber



Re: Shower Diverter Valve Temperature
Reply #3 - May 20th, 2021, 8:48pm
 
Nearly all the quality showers I know have the means to adjust the setup temperature, if you have the manual it would be in that, otherwise phone Roper Rhodes.

I'll assume you cleaned the filters as part of the checking earlier.

Out of interest is the temperature good at other outlets?
Back to top
« Last Edit: May 20th, 2021, 8:51pm by thescruff »  
Thank User For This Post View members image gallery  
IP Logged
 
Custard
Junior Member
**
Offline

Ask The Trades
Posts: 15


Total Thanks: 0
For This Post: 0



Re: Shower Diverter Valve Temperature
Reply #4 - May 22nd, 2021, 12:43pm
 
Hello – thanks for that,

The adjustment on the temperature set up is on maximum, i.e. the retainer is not in place yet as I wanted it at the maximum temperature. It's still not very hot.

Yes, I cleaned both filters

Yes, the temperature and pressure at all other outlets is very good.
Back to top
 
Thank User For This Post View members image gallery  
IP Logged
 
thescruff
Global Moderator
Trade Member
Author
*****
Offline

Who said plumbing was
easy.
Posts: 6037


Total Thanks: 147
For This Post: 0


Gender: male

Trade: Plumber



Re: Shower Diverter Valve Temperature
Reply #5 - May 23rd, 2021, 10:46am
 
Can we get technical?

What is the actual temperature from the shower?

What is the temperature of the hot from the boiler?

And what are the hot and cold pressures? you can time how long it takes to fill a measured bucket.

For comparison do the same checks at the kitchen sink.

If I have the above information I will pop in or phone Roper Rhodes and ask their technical guy.
Back to top
 
Thank User For This Post View members image gallery  
IP Logged
 
Custard
Junior Member
**
Offline

Ask The Trades
Posts: 15


Total Thanks: 0
For This Post: 0



Re: Shower Diverter Valve Temperature
Reply #6 - May 23rd, 2021, 12:36pm
 
Hello – that's very kind of you to offer to do that.

I have already been on to the Roper Rhodes technical guy and beyond a service and descale and clean the filters, he had no other suggestions to offer. He sent me a new thermostatic cartridge which didn't work and that's when I got in touch with you.

Before I cover the bits you asked for – I can say that the mains pressure is very good at my flat. Perhaps too good. I wonder if the pressure increased for some reason a few months ago. I've noticed that if I restrict the flow by doing up the internal stop cock a bit, the shower does get hotter and still has sufficient flow.

Is there anything wrong with that solution?
Back to top
 
Thank User For This Post View members image gallery  
IP Logged
 
thescruff
Global Moderator
Trade Member
Author
*****
Offline

Who said plumbing was
easy.
Posts: 6037


Total Thanks: 147
For This Post: 0


Gender: male

Trade: Plumber



Re: Shower Diverter Valve Temperature
Reply #7 - May 24th, 2021, 8:50am
 
It wouldn't be a problem they're only 5 miles up the road.

Back to your suggestion, yes it would be a future problem with the valve not turning off fully, although you can test doing it.

Best to buy an adjustable prv, (pressure reducing valve), but do the bucket test first so we know what we are looking at.

If the mains is that high, it would be best fitted near the incoming stopcock to reduce the hot as well.

Have you considered the problem may actually be the boiler? What is the make and model, also age.
Back to top
 
Thank User For This Post View members image gallery  
IP Logged
 
Custard
Junior Member
**
Offline

Ask The Trades
Posts: 15


Total Thanks: 0
For This Post: 0



Re: Shower Diverter Valve Temperature
Reply #8 - May 24th, 2021, 3:28pm
 
Hello

OK, I've done the bucket test. I had to do this in the kitchen (it's right next door to the bathroom) because, of course I can't reliably isolate hot/cold in the shower because of the thermostat. The Cold took 23 seconds to fill 8 litres. The hot 27 seconds. So I think (roughly):

Cold = 21 litres/min approx.
Hot = 18 litres/min approx.

The boiler is an Ideal Independent C24 and was here when I moved in October 2015. I took the pic below of the serial number but it also has a date that may be when it was made (2005)?

Independent C4

Just as an aside – this morning I opened the internal stopcock from fully closed about 1/2 - 3/4 of a turn so that I still had acceptable flow but reduced. The shower was plenty hot enough and with a good flow.

I can still easily shut off the supply in an emergency – my apologies – I didn't quite understand why not opening the stopcock fully is a bad idea.
Back to top
 
Thank User For This Post View members image gallery  
IP Logged
 
thescruff
Global Moderator
Trade Member
Author
*****
Offline

Who said plumbing was
easy.
Posts: 6037


Total Thanks: 147
For This Post: 0


Gender: male

Trade: Plumber



Re: Shower Diverter Valve Temperature
Reply #9 - May 25th, 2021, 9:55am
 
That is around 4 gallons/min or twice the boiler output, you need to fit an adjustable pressure-reducing valve.

Check hear for ideas. https://www.bes.co.uk/plumbing-supplies/brassware/pressure-equalising-reducing-a....

When the stopcock is not fully open the water will cut a groove in the seating and therefore will not turn off fully.
Back to top
« Last Edit: May 25th, 2021, 9:58am by thescruff »  
Thank User For This Post View members image gallery  
IP Logged
 
Custard
Junior Member
**
Offline

Ask The Trades
Posts: 15


Total Thanks: 0
For This Post: 0



Re: Shower Diverter Valve Temperature
Reply #10 - May 25th, 2021, 3:35pm
 
Oh right.  Undecided
Do you think that the pressure is unusually high? It does seem a bit harsh.

Can we reasonably assume it may not be a boiler issue?

I'm not sure I trust myself to tackle that kind job for the adjustable pressure reducing valve. I think I'd have to give that to a pro. I've been out of work for over a year so maybe it will have to wait £££. Not even sure where the external stopcock is  Huh

I took the pic below outside my flat. The pipe goes into the kitchen which where the internal stopcock is. Does this look like a likely candidate for the external stopcock? I don't suppose I could give that a little tweak to reduce the pressure could I? Think I know what you're going to say – or that it's a gas pipe!

Outside Pipe
Back to top
 
Thank User For This Post View members image gallery  
IP Logged
 
thescruff
Global Moderator
Trade Member
Author
*****
Offline

Who said plumbing was
easy.
Posts: 6037


Total Thanks: 147
For This Post: 0


Gender: male

Trade: Plumber



Re: Shower Diverter Valve Temperature
Reply #11 - May 25th, 2021, 5:04pm
 
Nope, can't tell the size of the pipe in your pic, but it looks like an old lead waste pipe from the sink.

Post a pic showing the valve you turned down to reduce the flow.

Also a pic of the pipes around the boiler (not too close)

Don't look a boiler problem other than the flow pressure
Back to top
« Last Edit: May 25th, 2021, 5:05pm by thescruff »  
Thank User For This Post View members image gallery  
IP Logged
 
Custard
Junior Member
**
Offline

Ask The Trades
Posts: 15


Total Thanks: 0
For This Post: 0



Re: Shower Diverter Valve Temperature
Reply #12 - May 26th, 2021, 2:30pm
 
Here's a shot of the boiler and where I've pulled the washing machine out to get at the pipework – no pipes visible above the worktop. ...

Image 8

...below the worktop. I have put the pics together in the order they run with a bit of overlap so you can see what's where. The stopcock is marked with a red arrow (and a label tied to it). There are two other spigots in the pic. One directly below the stopcock and one to the right and beneath the gas meter. No idea what they do...

Just FYI – The gas meter is in a corner. The wall where the white pipe and flexi hose is – is to the outside (where the old lead waste pipe pic was taken yesterday) and the wall where the stopcock and electrical socket is - is next door's kitchen.

Image 9


Let me know if you can't make sense of the pics – thank you.
Back to top
 
Thank User For This Post View members image gallery  
IP Logged
 
thescruff
Global Moderator
Trade Member
Author
*****
Offline

Who said plumbing was
easy.
Posts: 6037


Total Thanks: 147
For This Post: 0


Gender: male

Trade: Plumber



Re: Shower Diverter Valve Temperature
Reply #13 - May 29th, 2021, 10:50am
 
Sorry for the delay, Looks a bit tight for space, so, maybe best to get a plumber to look at it.

Is there a way to restrict the cold nearer the shower valve?
Back to top
 
Thank User For This Post View members image gallery  
IP Logged
 
Custard
Junior Member
**
Offline

Ask The Trades
Posts: 15


Total Thanks: 0
For This Post: 0



Re: Shower Diverter Valve Temperature
Reply #14 - May 29th, 2021, 2:09pm
 
No problem, thanks for the reply. I'd have to remove a load if stuff and the plasterboard from the store cupboard that backs onto the shower but it's a good thought. There might be one of those isolating valves with the quarter-turn to stop the flow. Is it OK to partially close those or will that damage it too?
Back to top
 
Thank User For This Post View members image gallery  
IP Logged
 
thescruff
Global Moderator
Trade Member
Author
*****
Offline

Who said plumbing was
easy.
Posts: 6037


Total Thanks: 147
For This Post: 1


Gender: male

Trade: Plumber



Re: Shower Diverter Valve Temperature
Reply #15 - May 30th, 2021, 8:20am
 
Yes, they can be partially closed, but please remember the cheaper models can leak from the shaft.
Back to top
 
Thank User For This Post View members image gallery  
IP Logged
 
Custard
Junior Member
**
Offline

Ask The Trades
Posts: 15


Total Thanks: 0
For This Post: 0



Re: Shower Diverter Valve Temperature
Reply #16 - May 30th, 2021, 7:09pm
 
OK – many thanks for your help with this. I'll give that a try if they exist behind the plasterboard but I'm not sure if I'd know a cheap one if I saw one!
Back to top
 
Thank User For This Post View members image gallery  
IP Logged
 
Pages: 1 2 
Send Topic Print