Ask The Trades - shaver socket

Welcome, Guest. Please Login or Register

	Apr 5^th, 2026, 4:57pm
View recently thanked users View top thanked users

Quote: Why do people without a watch look at their wrist when you ask them what time it is?

Ask The Trades › DIY Forum › Electrical Questions › shaver socket

(Moderator: Lectrician) - (Moderator Group: Board Moderator)

< Previous Topic | Next Topic >

Pages: 1

shaver socket (Read 6080 times)

oldspark GDPR opt-out	shaver socket Jul 2^nd, 2009, 9:57pm Mk logic plus type shaver supply unit to be installed in bathroom/washroom.Can I spur off up stairs ring main to feed unit , wire in ring main or supply seperatly direct from board? It will be 30mA RCD protected.
Back to top	IP Logged

Zambezi GDPR opt-out	Re: shaver socket Reply #1 - Jul 2^nd, 2009, 10:01pm Normally off the bathroom lighting circuit. I don't see why you could not take it off a ring but it may need a fused spur before the shaver socket.
Back to top	IP Logged

oldspark GDPR opt-out	Re: shaver socket Reply #2 - Jul 3^rd, 2009, 9:43pm Does anyone know BS 7671 Ammendment 3 1992 regarding shaver sockets?
Back to top	IP Logged

CWatters

Super Member

Offline

"Daddy fick it" says James

Posts: 5150

Total Thanks: 58
For This Post: 0

Gender: male

Re: shaver socket
Reply #3 - Jul 4^th, 2009, 2:17pm

Quote:

Does anyone know BS 7671 Ammendment 3 1992 regarding shaver sockets?

I believe thats all about "zones"...See for example...

http://www.allupandon.co.uk/lighting/information/bathroomzones

Electrical fittings in each zone must have a certain IP rating (or better). IP ratings refer to how dust and water tight the fitting is.

This MK shaver socket ...
http://www.tlc-direct.co.uk/Technical/DataSheets/MK/K701.pdf
..is rated IP41 so it's reasonably dust proof but not very waterproof. It must go outside zone 2.

« Last Edit: Jul 4^th, 2009, 2:22pm by CWatters »

IP Logged

wozzy Trade Member Offline Ask The Trades Posts: 584 Total Thanks: 4 For This Post: 0 Gender: Trade: Electrician	Re: shaver socket Reply #4 - Jul 4^th, 2009, 3:17pm is the zone around the sink a regulation or a recomendation? and isnt it usually 300mm not 600mm?
Back to top	All advice is at least two years out of date. IP Logged

GDPR opt-out

Total Thanks: 4
For This Post: 0

Re: shaver socket
Reply #5 - Jul 4^th, 2009, 9:03pm

wozzy wrote on Jul 4^th, 2009, 3:17pm:

is the zone around the sink a regulation or a recomendation? and isnt it usually 300mm not 600mm?

according to the diagrams in bs 7671 2008, there isn't a zone around the sink, the only time the sink would fall into zone 2 is if it were installed within 600mm of a bath or shower, I think the shaver socket needs to be mounted in a suitable position. Putting it right next to a tap wouldn't be suitable. If there is a zone around a sink, that's a recommendation by MK. It's not a reg, but manufacturers instruction override the regs. So when installing the MK shaver socket it has to be installed to their instruction.

Regards

Carl

« Last Edit: Jul 4^th, 2009, 9:07pm by cosbycarl »

IP Logged

Pages: 1

(Moderator: Lectrician) - (Moderator Group: Board Moderator)

< Previous Topic | Next Topic >

Ask The Trades › DIY Forum › Electrical Questions › shaver socket