Ask The Trades - warped 6 panel doors

Welcome, Guest. Please Login or Register

	Apr 24^th, 2026, 11:49am
View recently thanked users View top thanked users

Quote: Half the people you know are below average.

Ask The Trades › DIY Forum › Carpentry Questions › warped 6 panel doors

(Moderators: big_all, woodsmith, TIMBA-WOLF) - (Moderator Group: Board Moderator)

< Previous Topic | Next Topic >

Pages: 1

warped 6 panel doors (Read 4107 times)

sparxxxx Full Member Offline Posts: 435 Total Thanks: 0 For This Post: 0	warped 6 panel doors Jun 11^th, 2006, 5:40pm got 2 No 6 panel doors that are warped by about 20 mm top to bottom - about 20 years old probably from Taiwan or similar - therefore not top quality. Is there any way of straightening them or should I have a bonfire.
Back to top	IP Logged

big_all

Global Moderator
Trade Member
Author

Offline

heeelllooo
Posts: 5596

Total Thanks: 10
For This Post: 0

Gender: male

Trade: Joiner

Re: warped 6 panel doors
Reply #1 - Jun 11^th, 2006, 5:51pm

you wont straiten such an old door unless its gone because its been soaked [dipping ect] then it may return when dry

the usual way to deal with a door like this is spread it over the four corners

remove the doorstop

move the hinge diagonaly opposit the corner sticking out 5mm out
and the other hinge 5mm in towards the doorstop

this has the effect of placing a 5mm discrepancy in each corner

refit doorstop[new will be best ]

big all --------------- we are all still learning

IP Logged

sparxxxx Full Member Offline Posts: 435 Total Thanks: 0 For This Post: 0	Re: warped 6 panel doors Reply #2 - Jun 13^th, 2006, 6:14am Thaks ba, think I'll have a bonfire.
Back to top	IP Logged

big_all Global Moderator Trade Member Author Offline heeelllooo Posts: 5596 Total Thanks: 10 For This Post: 0 Gender: Trade: Joiner	Re: warped 6 panel doors Reply #3 - Jun 14^th, 2006, 7:23am dont blame you the only trouble is the new doors are likely to be poorer quality and just as warped unless you pay a bit more and check the door first
Back to top	big all --------------- we are all still learning IP Logged

CWatters

Super Member

Offline

"Daddy fick it" says James

Posts: 5150

Total Thanks: 58
For This Post: 0

Gender: male

Re: warped 6 panel doors
Reply #4 - Jun 15^th, 2006, 11:59am

If they aren't painted finished and you are going to burn them anyway... You could try this first ...

Throw a few buckets of water over them until well soaked. Jig them up on bricks and weight down with more so that they are twisted 20mm in the oppsite direction to the existing warp. Leave to dry for many days under cover. Works reasonably well for model aircraft wings (at least if the glue is waterproof).

IP Logged

TIMBA-WOLF Board Moderator Offline Timba-Wolf..... Var@*sh, should be banned!! Posts: 7158 Total Thanks: 15 For This Post: 0 KENT,(under a tree!!!!) United Kingdom Gender: Trade: Joiner	Re: warped 6 panel doors Reply #5 - Jun 15^th, 2006, 8:40pm Quote: at least if the glue is waterproof). and if not ........OOOOPPPPSS!!!
Back to top	AS HONEST AND LOYAL AS THE TIMBER-WOLF. --VAR@*SH, DON'T YOU SWEAR AT ME!! PAL!!&&I DON'T SUFFER FROM INSANITY- I DAMNED WELL ENJOY IT!!!!! IP Logged

Pages: 1

(Moderators: big_all, woodsmith, TIMBA-WOLF) - (Moderator Group: Board Moderator)

< Previous Topic | Next Topic >

Ask The Trades › DIY Forum › Carpentry Questions › warped 6 panel doors