Ask The Trades - rebating facility removed

Welcome, Guest. Please Login or Register

	Apr 22^nd, 2026, 4:38pm
View recently thanked users View top thanked users

Quote: The best way to remember your wife's birthday is to forget it once.

Ask The Trades › DIY Forum › Carpentry Questions › rebating facility removed

(Moderators: TIMBA-WOLF, woodsmith, big_all) - (Moderator Group: Board Moderator)

< Previous Topic | Next Topic >

Pages: 1

rebating facility removed (Read 4130 times)

big_all

Global Moderator
Trade Member
Author

Offline

heeelllooo
Posts: 5596

Total Thanks: 10
For This Post: 0

Gender: male

Trade: Joiner

rebating facility removed
Nov 16^th, 2006, 10:38am

am i the only one who thinks the fox can rebate but this feature has been ruled out by what is obviously an added bit off metal to gaurd against the end off the cutter block!!!!!!
this machine [on the side you can't see] http://www.rutlands.co.uk/cgi-bin/psProdDet.cgi/F22564

all you need do is remove the fence and alter the gaurd [remove the bit protecting the cutter block]

set the table for maximum depth off cut take a bit off 2by2" planed the length off the table pass over the table till the front off the wood is about 1/2" beyond the far end

reset table to required cut clamp the 2x2" "fence"in position when your happy your rebate is in the correct place draw a datum pencil line on the table this will allow accurate copying when you have to chop and change during machining

also make shure any openings are fully gaurded when not in use

if your in a comercial situation you need to check the regulations incase they now prevent rebating on this machine!!!!!!!!

« Last Edit: Nov 16^th, 2006, 12:00pm by big_all »

big all --------------- we are all still learning

IP Logged

woodsmith Global Moderator Trade Member Author Offline Posts: 4407 Total Thanks: 137 For This Post: 0 Gender: Trade: Joiner	Re: rebating facility removed Reply #1 - Nov 16^th, 2006, 9:23pm I would think you would be better off, finger wise, the keeping of that is, using a router table. It's not unfeasable that the guide could come in contact with the blades with dire results. It's not nearly as bad as removing the riving knife off a table saw though, but I don't know anybody who would do that
Back to top	IP Logged

TIMBA-WOLF Board Moderator Offline Timba-Wolf..... Var@*sh, should be banned!! Posts: 7158 Total Thanks: 15 For This Post: 0 KENT,(under a tree!!!!) United Kingdom Gender: Trade: Joiner	Re: rebating facility removed Reply #2 - Nov 16^th, 2006, 10:28pm I do W/S.. the local carpenter who's also a Magistraite!! now whats his name!!!.... ah i remember... ...Justice Thumbs!!!!!!! I am out of here!!!!!
Back to top	AS HONEST AND LOYAL AS THE TIMBER-WOLF. --VAR@*SH, DON'T YOU SWEAR AT ME!! PAL!!&&I DON'T SUFFER FROM INSANITY- I DAMNED WELL ENJOY IT!!!!! IP Logged

big_all

Global Moderator
Trade Member
Author

Offline

heeelllooo
Posts: 5596

Total Thanks: 10
For This Post: 0

Gender: male

Trade: Joiner

Re: rebating facility removed
Reply #3 - Nov 17^th, 2006, 7:18am

woodsmith wrote on Nov 16^th, 2006, 9:23pm:

I would think you would be better off, finger wise, the keeping of that is, using a router table. It's not unfeasable that the guide could come in contact with the blades with dire results.

It's not nearly as bad as removing the riving knife off a table saw though, but I don't know anybody who would do that Roll Eyes

the point here though keith is

its the end thats fully enclosed by the normal fence as well

so thinking about it the added gaurd must be to do with the dust extraction because thats the only time you need to remove the fence
thankfully theres a securing screw i can use to hold a removable fence when overhead dust extraction is required Roll Eyes

« Last Edit: Nov 17^th, 2006, 7:20am by big_all »